Design and analysis of welding fixture of Rack and Pinion assembly
Keywords:
Design, Analysis, Welding Fixture, Assembly of Cross Member. Assembly bracket.Abstract
All manufacturing industry used for assembly of component for used the welding fixture. The fixtures are the important part of the welding as fixtures are used in manufacturing of different products during welding to hold the different parts of that respective product. Fixture having direct impact for the productivity and quality of product. welding fixture are design for the component which have difficult to weld. In normal way welding of different parts of component not possible for without holding device. The welding fixture are important holding device. The number of parts to be welded in proper position in fixture and tightened. When the fixture are holding work piece for produced by the welding stress. The proposes a design and analysis approach in fixture of sheet metal assemblies for rack and pinion Cross member component. The design of an assembly fixture for a particular tail cone has been completed convenient to the existing locating principles. In rack and pinion assembly manual clamping done due to different force produce. which have analysis by Stress deformation of component The design of welding fixture for this assembly component using for Pro-E and CAD software. using the Finite Element Analysis (FEA) by using ANSYS software that provides best output within few seconds. All part parts have design in Pro-E and different Load analysis done by ANSYS 14.5.
References
[1] Jigar D Suthar, K.M Patel, Sanjay G Luhana “Jigar D Suthar, K.M Patel, Sanjay G Luhana” International journal of Engineering Science Direct and Technology , vol. 51 ( 2013 ) 514 – 519
[2] Naveen A M, V A Girisha, Pruthvi H M “Design And Analysis Of Welding Fixture For Motor Case Assembly” On IJMPE, ISSN: 2320-2092, Volume- 2, Issue-8, Aug.-2014
[3] Kalpesh Khetani, Jafar Shah, Vishal Patel “ Design and Thermal Stress Analysis of Welding Fixture of a Brake Pedal” IJRMEE ISSN: 2349-7947 Volume: 2 Issue: 5 029 – 032,May-2015.
[4] Chetan D. Borse, Prasad V. Thete, Ravi P. Vishwakarma, Jainendrakumar S. Yadav “ Design And Analysis Of Fixture For A Stone Crusher Body” On IJRET eISSN: 2319-1163 | pISSN: 2321-7308, Volume: 04 Issue: 06 | June-2015.
[5] A. M. Mhaske, R. M. Metkar, S. D. Hiwase “Design and Analysis of Welding Fixture for Tacking and Welding of Inner Boom of Loadall Handler” On IJRMET, ISSN : 2249-5762, Vol. 5, Issue 2 ,May - Oct 2015
[6] Omkar Joshi, Dr. Arunkumar “ Design And Analysis Of Welding Fixture For Orbital Welding Machine”On IJPME, Volume III Issue IV October – December 2015
[7] Vaishak bhandary M, Sudeep N S, Naveenakrishna P V “Design and Analysis of Robot Full Welding Fixture for Front Chassis of Wheel Loader” NCAMES ,ISSN: 2231-5381- 2016
[8] C. A. Kubade , Dr. S.V. Patil , Mr. V. P. Patil “Design and Analysis of Welding Fixture for Automotive Component using FEA” IJARIIE-ISSN(O)-2395-4396, Vol-2 Issue-4 20
[9] Vishala, P. Sampath Rao “Analytical Report Based on the Design and Simulation of a Weld Fixture” SSRG International Journal of Mechanical Engineering (SSRG-IJME) – volume1 issue 5 September 2014
[10] Prof. A. A. Karad,Brijeshwar Wagh, Ajay Shukla[, Niladhari Pyata ,Chetan Gujar “Design and Analysis of Welding Fixture for Fuel Tank Mounting Bracket” International Journal of Engineering Research and General Science Volume 4, Issue 2, March- April, 2016 ISSN 2091-2730
Downloads
Published
Issue
Section
License
This work is licensed under a Creative Commons Attribution 4.0 International License.
This work is licensed under a Creative Commons Attribution 4.0 International License.
Under this license, authors retain ownership of the copyright for their articles. By submitting to the International Journal of Advanced Research in Science, Management, and Technology (IJARSMT), authors grant the journal the right of first publication. Users are free to share, copy, and redistribute the material in any medium or format, and to adapt, remix, transform, and build upon the material for any purpose, including commercially, provided that appropriate credit is given to the original author(s) and the journal, a link to the license is provided, and any changes made are indicated.
